Policies

School Lifting Operations and Equipment Management Procedure

This procedure applies only where a maintained or academy primary or secondary school in England provides, hires, controls or uses lifting equipment or carries out lifting operations. It sets out how the school identifies lifting equipment and accessories, plans and supervises lifting operations, appoints competent and sufficiently independent examiners, controls installation and relocation, checks safe-working-load information, arranges thorough examinations, retains reports and acts on defects. Routine servicing or maintenance does not replace a required LOLER thorough examination.

SOP Template
CalmComplianceSOP Template

School Lifting Operations and Equipment Management Procedure

Version
v2
Updated
7 October 2026

Fields in brackets are completed when you adapt this template.

This procedure applies to [school name] only where the school provides, hires, controls or uses lifting equipment or carries out lifting operations. It is for maintained and academy primary and secondary schools in England and does not apply to independent schools.

Responsibilities

The school should assign responsibility for implementing this procedure to [responsible role]. The person responsible should ensure that lifting equipment and accessories are identified, lifting operations are planned and supervised, examinations are arranged where required, reports are retained and defects are addressed.

Identify equipment and accessories

Identify lifting equipment and lifting accessories that the school provides, hires, controls or uses. The arrangements should cover equipment such as lifts, hoists, mobile elevating work platforms, fork-lift trucks, chains, slings and eyebolts where these are present.

Record each item in an equipment register with an identifier that can be matched to its examination report. Record whether the equipment lifts loads, lifts people or is a lifting accessory, because the applicable thorough-examination interval depends on that use.

Plan, supervise and carry out lifting operations safely

Every lifting operation must be properly planned by a competent person, appropriately supervised and carried out safely. The competent person should have adequate practical and theoretical knowledge and experience of planning the lifting operations being undertaken.

A formal written plan is not required for every individual lifting operation. Where there is a significant change from standard practice, provide additional planning to address the change and ensure that the operation can be carried out safely.

Safe working load information

Before equipment or accessories are used for lifting loads, ensure that they are clearly marked or otherwise provided with information indicating their safe working load. Where the safe working load depends on the configuration, provide the safe working load for each configuration or keep the relevant information with the machinery.

For chain and wire slings, the safe working load should be marked legibly and indelibly on a durable tag or label attached to the sling, or on the ferrule or master link. Colour coding alone is not normally sufficient to indicate the safe working load.

Competent and sufficiently independent examiners

Arrange LOLER thorough examinations only with a competent person who has suitable practical and theoretical knowledge and experience of the equipment. The competent person must also be sufficiently independent and impartial to make objective decisions.

The person who routinely services or maintains the equipment should not normally conduct its thorough examination, because that person would be assessing their own work. Keep routine servicing and maintenance arrangements distinct from the thorough-examination responsibility.

New, installed, assembled or relocated equipment

Before first use, arrange examination of new lifting equipment unless it has a valid Declaration of Conformity that is less than one year old and the equipment was not assembled on site and does not depend on the conditions of installation for safety.

Where equipment is assembled on site or depends for safety on how it is installed, arrange examination by a competent person to confirm that the assembly or installation is correct and safe. For equipment requiring assembly or installation before use, arrange examination after assembly and before use at each location.

Apply the same control when equipment is relocated and requires assembly or installation at the new location. Do not put the equipment into use at that location before the required examination.

Hired lifting equipment

When hiring lifting equipment, satisfy the school at the outset that a current thorough-examination report is available. Match the report to the hired equipment and retain the report or the relevant evidence with the hire records.

Thorough-examination intervals

Unless a written examination scheme drawn up by a competent person specifies different intervals, arrange thorough examination of lifting equipment used to lift loads every 12 months.

Arrange thorough examination every 6 months where the equipment is used to lift people. Arrange examination every 6 months for lifting accessories.

A competent person may specify a more rigorous examination scheme where, for example, equipment is used in extreme temperatures, a potentially corrosive environment or particularly heavy use, or where failure could have potentially catastrophic consequences. An examination scheme may exceptionally specify longer intervals where the competent person determines that deterioration will be very slow or a sampling and inspection scheme is appropriate.

Event-triggered examinations

Arrange a further thorough examination after any accident or dangerous occurrence, any significant change in conditions of use, the replacement of parts subject to thorough examination, or a long period of inaction.

If routine servicing includes fitting new parts covered by LOLER, arrange a thorough examination before the equipment is used.

Reports, defects and continued use

Retain written thorough-examination reports and ensure that each report can be linked to the relevant item of equipment or accessory. Record the applicable next-due date and any restrictions, recommendations or defects identified by the competent person.

Act on defects identified in a thorough-examination report. Where a defect affects safe use, follow the competent person's direction about continued use and do not treat routine servicing or maintenance as a substitute for the required thorough examination.

Sources

  1. Equipment and machinery frequently asked questions (FAQs) - HSEHealth and Safety Executive (HSE)
CalmCompliance · v2Template for adaptation

Template details

Type
SOP Template
Version
v2
Updated
7 October 2026
Sections
32 sections
  • Equipment and machinery frequently asked questions (FAQs) - HSE

Get this template

Free, editable Word document. We’ll email you a download link. No Calm account needed.

Edit in Word or Google Docs.

We record your email and the template you request. Read our privacy policy.